Product Center
Home » oxyfuel gas cutting machine diagram printable
  • Gas Welding, Cutting Torches & Oxy-Fuel Equipment

    ADVERTISEMENTS: After reading this article you will learn about:- 1. Process of Gas Cutting 2. Efficiency of Gas-Cutting 3. Equipments 4. Limitations. Process of Gas Cutting: Apart from using hacksaw, power saw, chisels, etc. for metal cutting operation, gas or oxygen cutting is extensively used now-a-days in industry. Oxy-fuel cutting (OFC) is similar to ox […]

  • Oxyfuel Cutting - Process and Fuel Gases - TWI

    Lighting the Oxy-fuel torch 1. Turn the acetylene knob on the cutting torch about a quarter of a turn and light the acetylene. Make sure that the flame is up against the tip. If you light up the tip and the flame is away from the tip, decrease the acetylene pressure and let the flame come back against the tip. (Use your safety equipment ...

  • Oxyfuel Cutting - Process and Fuel Gases - TWI

    Our CNC oxy-fuel machines are designed for cutting mild steel plates up to 3” thick, stainless steel up to 4” thick as well as aluminum up to 3” thick. Each of the machines can be configured for plasma cutting, oxy-fuel cutting or both.

  • Oxy Acetylene Welding Equipment | HobartWelders

    Oxyacetylene gas welding is commonly used to permanently join mild steel. A mixture of oxygen and acetylene, burns as an intense / focussed flame, at approximately 3,500 degrees centigrade. When the flame comes in contact with steel, it melts the surface forming a molten pool, allowing welding to …

  • How Does The Oxy-Fuel Cutting Process Work? | Park Industries

    Victor introduced the EDGE™ regulator changing the landscape of gas regulation. 2012 Victor manufacturing team worked overtime to produce over 5,000 pieces of equipment including special 15 and 20 foot length cutting torches to help with 9/11...

  • What kind of metal can you cut with oxy fuel?

    Oxy-Fuel Setup and Troubleshooting The torch is held in position by the use of a machine torch holder that is attached to the Y axis gantry cassette. The solenoid switch is attached to the Oxygen air line, and is then wired to a 110 volt type of plug, that can be inserted into the Output #1 on the Machine …

  • Cutting Machine Solutions | Plasma and Oxy-fuel

    Primary Category: ~Welding~Gas Welding Equipment and Accessories~Oxy-Fuel Cutting Machines. $5,967.00 / each. Qty. Please enter a numeric value. Add to Cart. Note: Product availability is real-time basis and adjusted continuously. The product will be reserved for you when you complete your order. Back to Top 2 Products.

  • Used Oxyfuel Cutting Machines for sale. Messer equipment ...

    Chart and Diagram Slides for PowerPoint - Beautifully designed chart and diagram s for PowerPoint with visually stunning graphics and animation effects. Our new CrystalGraphics Chart and Diagram Slides for PowerPoint is a collection of over 1000 impressively designed data-driven chart and editable diagram s guaranteed to impress any audience.

  • Oxygen And Acetylene Use And Safety - Virginia

    Jan 25, 2017 · Oxy acetylene gas welding cutting choosing oxy fuel vs plasma cutting unled oxy acetylene welding equipment diagram c welding hoses Acetylene Vs Alternate Fuel The Harris S GroupOxy Acetylene Welding Ofw Fundamentals Pressure Settings Chart Set Up And KitNeed Help Selecting An Oxy Acetylene Setup Bike ForumsDid You Know That Gas Flames Produce Infrared …

  • Cutting Torches & Replacement Parts by Thermal Dynamics ...

    Typical edge conditions resulting from oxyfuel gas cutting operations: (1) A good cut in 1″ (25.4mm) plate. The edge is square, and the drag lines are essentially vertical and not too pronounced. (2) The preheat flames were too small for this cut, and the cutting speed was too slow, causing bad gouging at the bottom.

  • Comet Blowpipes Cutting Attachments and Consumables

    Oxyfuel cutting (OFC), also called flame cutting or burning, is a process that uses the flame and oxygen from a cutting torch to cut ferrous metals. The flame is produced by burning a fuel gas mixed with pure oxygen. The flame heats the metal to be cut to the kindling temperature (a cherry red color).

  • How Does The Oxy-Fuel Cutting Process Work? | Park Industries

    Oxy-Fuel Gas Welding I. Competencies Given a functional oxy-fuel gas unit, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the oxy-fuel gas unit. B. Pass a written test on safety and operation procedures on the oxy-acetylene unit with a minimum of 100 accuracy.

  • CNC Gas Cutting Machines - CNC Gas Cutting Machine ...

    used for a variety of applications. Oxy-fuel equipment is versatile, lending itself to welding, brazing, braze-welding, silver soldering, metal heating (for bending and forming) and oxy-fuel cutting. This book will highlight the welding and cutting processes. Table of

  • What kind of Workbench do I need to cut oxy fuel?

    ALLtra's Oxy-fuel Cutting Capabilities. ALLtra Corporation offers cutting machines with oxy-fuel stations that provide consistent results from a single or multiple station cutting machines, including the PG-14 and HG-30. ALLtra oxy-fuel cutting machines include key features such as high speed torch positioning, digital control of the preheat and cut gases, and options for automatic height control.

  • Oxy-Fuel Cutting Quiz Answers - ctaeir.org

    Oxy Fuel Gas Cutting - KOIKE MACHINE-0

  • Oxy-fuel cutting | Gas Cutting process working principle ...

    metal powder. Typical oxygen cutting processes are oxyfuel gas, oxygen arc, oxygen lance, metal powder and chemical flux cutting. 2.1. Oxyfuel Gas Cutting Oxyfuel gas cutting processes sever or remove metal by the chemical reaction of oxygen with the …

  • Arc & Gas Welding & Cutting Equipment

    Oxy-fuel welding (commonly called oxyacetylene welding, oxy welding, or gas welding in the United States) and oxy-fuel cutting are processes that use fuel gases (or liquid fuels such as gasoline) and oxygen to weld or cut metals. French engineers Edmond Fouché and Charles Picard became the first to develop oxygen- acetylene welding in 1903.